PDF Knight Space Spanner Manualsearch tools to find only free Google eBooks. Knight Space Spanner Manual A Knight Space Spanner. This was built by James Kasper in 1957 or 1958.If the refrigerator is not leveled, unsteady, vibrating, or the doors are not closing properly then we need to level it. All of its essential components and connections are illustrated by graphic symbols arranged to describe operations as clearly as possible but without regard to the physical form of the various items, components or connections. It is a regen radio and was sold as a kit by Allied Radio. Page 4/24Fiat 500 spare tire location -. The Space Spanner manual is 11' x 8 1/2'.
Space Spanner Driver Into TheThe first step is to level the unit from left to right, using a level across the top of the cabinet. Proceed to Next StepIf the refrigerator compartment door is lower than the freezer compartment door, we need to level it.Level the door by inserting a flat blade screwdriver into the groove of the RIGHT leveling leg.If you prefer to lower freezer compartment you ned to turn the leveling leg counter-clockwise to align with the refrigerator compartment door.Place a level on the top of the refrigerator doors to determine if the individual doors need additional leveling.Note: Due to the wide variety of french door models, we recommend that you refer to the owner's manual for specific model instructions.French door models (either three doors or four doors), have more steps in the leveling process. It may take several turns of the leveling leg to adjust the tilt of the freezer compartment.If you prefer to lower freezer compartment you need to turn the leveling leg counter-clockwise to align with the refrigerator compartment door.Place a level on the top of the refrigerator doors to determine if the individual doors need additional leveling. This makes it easier to adjust the legs.Turn the leveling leg clockwise to raise the freezer compartment door. To access the leveling feet, the lower cover must be removed.Remove the screws on the kick plate grille (some models do not have a kick plate, only follow this step if it is applicable).Remove the kick plate to access the leveling screws.The side-by-side model has two leveling screws, one on the right, and one on the left.Level the door by inserting a flat blade screwdriver into the groove of the LEFT leveling leg.Having someone push backward against the top of the refrigerator takes some weight off of the leveling legs.Turn the leveling legs counterclockwise to raise them or clockwise to lower them.With one hand, lift up both the inner and outer door sections to raise them at the middle hinge (opening the door can make lifting easier).With the other hand, use pliers to insert the snap ring on the middle hinge of the inner door section as shown. Insert one at a time until the doors are aligned.Remove the screws on the kick plate (some models do not have a kick plate, only follow this step if it is applicable).Level the refrigerator by using a wrench or a flathead screwdriver. The new french door model comes with two or three snaps (depending on the model). After the unit is leveled, insert the snap rings on the hinge pin of the refrigerator door to raise the lower door. For new models, 2006 and above, snap rings are used to allow more precise door alignment.Space Spanner Free Google EBooksAfter the unit is leveled with the leveling feet, use the wrench supplied with the unit to adjust the door height. For units with this feature, snap rings are no longer used to align the doors. Using the snap ring on the outer door hinge can cause the door not to open and close properly.NOTE: Some specific models produced from 2008 and above have an AUTO CLOSING HINGE feature. ![]() There are only two leveling feet, and they are positioned in front of the two front wheels. The two in the back can move from front to back, while two in the front can move and turn to the sides. For new installations, allow the refrigerator to run for at least four hours before storing food.Once the unit is leveled, place back the kick plate, check the freezer door to ensure that it is aligned properly, and there is no gap between the freezer door and the cabinet.If you see any gap, make sure that all the screws attaching the door to the guide rail are inserted and tightened properly.There are four wheels on the unit. The door should shut by itself when opened at a 45-degree angle.Have someone hold the freezer door, so that the space between the two doors is even, and re-tighten the top hinge bolts if needed.If the refrigerator had frost buildup allow 72 hours for the defrost cycle to eliminate the frost. Amd fx 8150 benchmarkThe refrigerator must not have any side tilt, use the front legs to balance each side. Turn the leveling legs clockwise to raise the unit, or counterclockwise to lower it. The leveling legs can be turned easily by having someone push the unit against the wall to remove some weight off the feet. If required, adjust the leveling legs to compensate for unevenness of the floor. Boroughsburg sims 3 fileIf you are having difficulties with lowering the legs, lightly tilt the refrigerator backward, and place a wooden block under the front edge. The door should shut by itself when opened at a 45-degree angle. To achieve a balanced rear tilt, turn the leveling screws at the same amount of rotation.
0 Comments
Leave a Reply. |
AuthorKristen ArchivesCategories |